|
|
|
BRAKE EXTENSION.
Center the drill bit in the brake lever, and drill the rest of the way.... |
|
SHIFT EXTENSION.
To install the shift extension you simply push the shift extension... |
|
SIDE STAND FOOT, R1200RT.
Remove the two screws and the top plate. |
|
PASSENGER SPORTBOARD AND RISER, R1100RT, R1150RT, R1200RT.
Fit mounting bracket into clevis on footrest plate and install clevis pin. Reinstall... |
|
SPORTBOARD, DRIVER, R1150RT.
Fit mounting bracket into clevis on footrest plate and install clevis pin. At this point the Sportboard.... |
|
SPORTBOARD, DRIVER / SIDESTAND FOOT COMBO, R1200RT.
Fit mounting bracket into clevis on footrest plate and install clevis pin. At this point the Sportboard... |
|
SPORTBOARD, DRIVER, K1200LT, 1998-CURRENT.
Fit mounting bracket into clevis on footrest plate and install clevis pin. At this point the Sportboard... |
|
SPORTBOARD, DRIVER, K1200LTC, 1998-CURRENT.
Fit mounting bracket into clevis on footrest plate and install clevis pin. At this point the Sportboard... |
|
SPORTBOARD, DRIVER, R1200C.
Install a wave washer on either side of the mounting bracket of the footrest plate and fit it.... |
|
PASSENGER RISER, K1200LT, 1998-CURRENT
Install the riser bracket to the mounting bracket and reinstall the two ¼-20 button head screws. Apply a thin film of grease.... |
|
PASSENGER RISER, K1200LTC, 1998-CURRENT.
Install the riser bracket to the mounting bracket and reinstall the two ¼-20 button head screws. Apply a thin film of grease.... |
|
PASSENGER SPORTBOARD, K1200LT, 1998-CURRENT.
Apply a thin film of grease to both sides of the pivot on the passenger board where the clevis pin... |
|
PASSENGER SPORTBOARD, K1200LTC, 1998-CURRENT.
Install the clevis pin (install pin thru the side with the stainless steel plate first, it will be easier... |
|
|
|
|
|
|
|
SPORTBOARD, DRIVER and SIDE STAND FOOT COMBO, K1200GT, 2005-2007.
Fit mounting bracket into clevis on footrest plate and install clevis pin. At this point the Sportboard... |
|
BAR BACK, R1200GS / ADVENTURE 2005 - 2007.
Tighten the 8MM bolts to 17 ft lbs, with clean dry threads. Stock hoses and cables will work... |
|
BMW HIGHWAY PEGS, R1200RT, 2005 - 2009.
For all R 1200 models, install one side and tighten before going on to the other side. Loosen and remove the M12x50 Torx screw... |
|
BMW HIGHWAY PEGS, HORIZONTAL MOUNT, R1200GS.
Using 4 ea. of the 10-32 Allen screws and the 5/32” Allen wrench lightly clamp the highway pegs... |
|
BMW HIGHWAY PEGS, FRONT ENGINE GUARD MOUNT, R1200GS / GSA.
Using 4 ea. of the 10-32 Allen screws and the 5/32” Allen wrench lightly clamp the highway pegs... |
|
Highway pegs for Ilium Works engine guard bar system.
Place motorcycle on its center stand on level ground.
Using 4 ea. of the 10-32 Allen screws and the 5/32” Allen wrench lightly... |
|
BMW HIGHWAY PEGS, DOHC R1200RT, 2010-2012.
For all R 1200 models, install one side and tighten before going on to the other side. Loosen and remove the M12x50 Torx screw... |
|
Driver Sport boards, K1600GT / GTL.
Check to see that neither of the two ¼-20 nylon tipped setscrews are protruding from backside of mounting bracket.
Fit mounting bracket into clevis on footrest plate.....
|
|
These BMW motorcycle accessory are a combination of passenger risers and floorboards. With this combination you can adjust, raise the passenger foot location in 10 positions... |
|
HIGHWAY PEGS, FITS STOCK ENGINE GUARD BARS, K1600GT/GTL.
Using 4 ea. of the 10-32 Allen screws and the 5/32” Allen wrench lightly clamp the highway pegs.... |
|
Ilium Works engine guard system. Remove lower front fairings, right and left. Remove the two T25 Torx screws on the bottom of each side, and the two T25 Torx on the inside just behind the front wheel. There is also a locating tab inserted.... |
|
Versatile Highway Peg.
Because of the extreme flexibility of this mounting system there are many different mounting configurations... |